論文標準WORD格式排版 14頁

【中文摘要】本文介紹了吉利汽車總裝廠的生產流程工藝,著重從產品生產的裝配線,運用“一個不忘，ECRS四大原則，和六大提問技術”通過對總裝線的構成、工藝布置、設備、工裝等的全面分析，找出影響汽車生產能力的主要因素，充分考慮新產品的結構變化方向和市場需求的趨勢，利用工廠現有設施，采用最經濟合理、見效快的技術改造方案，實現生產綱領的目標。
【英文摘要】This article introduced the auspicious automobile general equipment department factory production process craft, from the product production assembly line, the utilization;does not forget emphatically, four big principles, five aspects and six big inquiry technologies through to the constitution, the craft arrangement, the equipment, the work clothes which always installs wiring and so on the comprehensive analysis, discovers the influence automobile productivity the primary factor, considered fully the new product the structural change direction and the market demand tendency, uses the factory existing facility, uses economically, reasonable, the effective quick technological transformations plan, the realization production guiding principle goal.

關鍵詞 裝配線 改造 工藝分析 生產能力 人性化 降低勞動強度

目 錄
1公司概況…………………………………………………………………………1

2工廠的現狀…………………………………………………………………………………1
2.1 裝配線結構、狀況平面圖 ………..………………………………………….1
2.2裝配線工藝流程………………………………………………………………1

3運用提問技術進行分析……………………………………………………….2
3.1現對B工段的幾個工序的分析………………………………………………………2
3.2對C工段的幾個工序進行分析………………………………………………………4

4.運用因果關系法找出重點……………………………………………………5

5 對現已發現的重點問題進行分析改善……………………………………6
5.1對裝配發動機，變速器的耗時的改進…………………………………………6
5.2 對工人的勞動強度大，底盤下裝配易疲勞的改進…………………………6
5.3 對加注油的改進………………………………………………………………6
5.4對玻璃裝配的改進……………………………………………………………7
5.5對儀表的裝配復雜改進………………………………………………………8

6.最終方案的確定………………………………………………………………8
6.1對裝配發動機，變速器的耗時的改進的選擇…………………………………8
6.2對工人的勞動強度大，底盤下裝配易疲勞的改進的選擇……………………8
6.3對加注油的改進的選擇…………………………………………………………8
6.4對玻璃裝配的改進的選擇………………………………………………………9
6.5對儀表的裝配復雜改進選擇……………………………………………………9
7結束語……………………………………………………………………………9