125t通用橋式起重機設計（結構部分）畢業設計

目 錄
摘要............................................. III               
前言............................................1
第一章  橋式起重機金屬結構設計參數 ....  2
第二章 .總體設計 3
   2.1 大車軸距 3
   2.2 主梁尺寸 3
第三章  主端梁截面積幾何性質 4
第四章、載荷 5
   4.1 固定載荷 5
   4.2 小車輪壓 5
   4.3 動力效應系數 6
   4.4  慣性載荷 6
   4.5  偏斜運行側向力 6
   4.6  扭轉載荷 8
第五章 主梁計算 9
   5.1  內力 11
   5.2  強度 14
   5.3  主梁疲勞強度 16
   5.4  主梁穩定性 18
第六章、 端梁計算 25
   6.1  載荷與內力 26
   6.2  水平載荷 27
   6.3  疲勞強度 31
   6.4  穩定性 34
   6.5  端梁拼接 35
第七章 、主梁和端梁的連接 39
第八章 、剛度計算 40
   8.1  橋架的垂直靜剛度 40
   8.2  橋架的水平慣性位移 41
   8.3  垂直動剛度 41
   8.4  水平動剛度 42
第九章、橋架拱度 43
  總結 45
  參考文獻 46
  致     謝 47
  英文資料 48

 
摘要
本設計采用許用應力法以及計算機輔助設計方法對橋式起重機橋架金屬結構進行設計。設計過程先用估計的橋式起重機各結構尺寸數據對起重機的強度、疲勞強度、穩定性、剛度進行粗略的校核計算，待以上因素都達到材料的許用要求后，畫出橋架結構圖。然后計算出主梁和端梁的自重載荷，再用此載荷進行橋架強度和剛度的精確校核計算。若未通過，再重復上述步驟，直到通過。由于橋架的初校是在草稿中列出，在設計說明書中不予記錄，僅記載橋架的精校過程。設計中參考了各種資料,運用各種途徑,努力利用各種條件來完成此次設計.本設計通過反復斟酌各種設計方案,認真討論,不斷反復校核,力求設計合理;通過采取計算機輔助設計方法以及參考前人的先進經驗,力求有所創新;通過計算機輔助設計方法,繪圖和設計計算都充分發揮計算機的強大輔助功能,力求設計高效。

關鍵詞:橋式起重機,校核,許用應力
 
Metal Framework Of Bridge Crane(10t 25.5m) Design

Abstract
The project designs metal framework of bridge crane in use of allowable stress method and CAD. At first ,I chose size assumably.Then, proofreaded the size.If the proof was not passed,must choose the size again up to pass the proof.If the proof was passed,it could carry on the specific structural design.At last,it’s plot and clean up the calculation process. Designed to make reference to the various of data in the process, make use of various paths, work hard to make use of the various of condition to complete this design in reason. I considered various design projects, discussed earnestly,calculated time after time, try hard for a  reasonable design;via CAD and make reference advanced experiences,try hard for a  innovatory design;via CAD,ploting and calculation can make good use of powerfull computer,try hard for a high efficiency design.I knew the various of design methods,newest machine design methods both here and abroad also found various of good data.
Key Words:bridge crane,proofread,allowable stress